Ssc service utility: sscig.com/epsone.shtml

SSC SERVICE UTILITY: SSCIG.COM/EPSONE.SHTML MANUAL
SSC SERVICE UTILITY: SSCIG.COM/EPSONE.SHTML SOFTWARE
SSC SERVICE UTILITY: SSCIG.COM/EPSONE.SHTML CODE

Select function with RESUME press POWER to execute: Let green light blink until printer is done futzing Press RESUME twice, and then release POWERД¤. Hold down RESUME and then hold down POWERДЈ.

SSC SERVICE UTILITY: SSCIG.COM/EPSONE.SHTML SOFTWARE

Remark 'After service mode please use software for permanent reset'ДЎ. Choose (SET DESTINATION 1) and it should be reset. Open General Tools software and select (USB PORT)ДЈ.

Close door, then release power button orДў. Press and release the RESUME button again, the indicator (L.E.D.) should be greenД¤. Press and release the RESUME button again, the indicator (L.E.D.) should be green.ДҐ. Press and release the RESUME button, the indicator (L.E.D.) should be orange.ДҐ. The indicator (L.E.D.) should be green.Д¤. Press and hold the POWER button, turn on the printer.ДЈ.

SSC SERVICE UTILITY: SSCIG.COM/EPSONE.SHTML MANUAL

Waste Ink Counter Manual Reset for Service modeДЎ. Press the POWER button again to restart the printer. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)ДЄfter selecting the desired mode (e g 4), press the POWER button to 'set' the change, and return to the top of the function selection menu. Service/Factory test printout, including ink sensor check.ДҐ. The lamp will alternate (change) color with each key press.ДЎ. (4) Press the RESUME button 4 times this will select the clear waste ink counter function. If the above was properly performed the printer will enter the 'Service Mode'. The printer's carriage will 'reset' or move momentarily.

(3) Release the RESUME button, Next press and release the RESUME button two (2) more times in succession. (2) Press and hold the RESUME button, then press and hold the POWER button. Orange and green, starting with orange.)note: press 4 times for waste ink counter reset.ДҐ) Turn off the printer.( it must be turn off) (Waiting for menu selection)Д¤) When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to theДЇunction listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in to make it simple for others out there this is the instructions i followed:ДЎ) With the printer powered off but connected to a power source, press the Power button while pressing and holdingДў) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.ДЈ) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a its only a matter of people like you with good will to help others out there from all parts of the world. I save a lot of time and money i don't have to sent my printer back to canon for their 'service'.

SSC SERVICE UTILITY: SSCIG.COM/EPSONE.SHTML CODE

Hello to you guys! thank you very much the code that you have provided for my canon pixma mp150 was really a great help. The carriage should return to its normal position. The printer will make some noise as it starts back up.Move the carriage all the way to the right, close the lid and reconnect the power cord.Unplug the power cord and remove the paper from the paper tray.If the carriage still won't move, or makes a grinding noise, continue on to the next step. The unit should re-start and move the print carriage to the normal position. Reattach the rear access door and reconnect the power cord.Open the rear access door and remove any paper from the paper path.If the printer fails to print, the Power light is blinking, a Mechanism Error is displayed on the computer, or the print cartridge carriage won't move back and forth across the printer, the carriage may be stalled. HP Deskjet 3535, 3744, and 3920 Color Inkjet Printer The Print Carriage is Stuck and Won't Move

Ssc service utility: sscig.com/epsone.shtml